Aerocel® continuous tube pipe insulation in unslit tubular form can be slipped onto piping before it is connected, or it can be slit lengthwise and snapped over piping already connected. Butt joints and seams are to be sealed with Aeroseal contact adhesive. Both surfaces to be joined must be coated with adhesive.
Self-adhering EPDM rubber tape for insulation tube and sheet joints. Provides extra protection against humidity.
PROTAPE is a EPDM-based self-adhering rubber tape, specifically designed for adhering the joints of Aerocel® tubes and sheets. Protape provides extra holding strength to the joints and serves as a vapor barrier to prevent atmospheric moisture from penetrating the seams. It is easy to wrap or patch tightly to insulation surfaces.
Description
Aeroseal adhesive (amber or black in color) is a modified neoprene contact adhesive specially formulated for bonding Aerocel® insulating materials firmly together. Aeroseal creates strong seams and butt joints that will operate at temperatures up to 257 degrees F. Aeroseal may also be used for adhering sheet insulation to flat and curved surfaces that will operate at temperatures to 180 degrees F. Aeroseal adhesive (amber or black) is also ideal for use with other materials like metal, cork board, polyurethane foam, rigid PVC sheet, formica, melamine board and rubber sheet. Aeroseal adhesive has a high water vapor resistance and weathering resistance to prevent moisture from penetrating joints, and forms a permanent bond to the applied materials for long lasting service.
Directions for Use
Stir contents thoroughly before use. Thinning is not recommended. Prepare both surfaces before applying adhesive by being sure they are dry and clean of any foreign matters. Apply a thin even coat to both surfaces to be bonded. Allow to dry but still tacky to the touch. Aeroseal will bond immediately upon contact, so it is necessary to position pieces accurately as contact is made. Moderate pressure should be applied over the entire area to assure that contact is complete.
It is recommended that the adhesive not be open for more than 10 minutes at a time and be applied only at temperatures above 40 degrees F. Do not apply to heated surfaces. If application is necessary under 40 degrees, extra care must be taken in application and closing the joint. Application below freezing (32 degrees F) is not recommended.
Where application is in an area that will operate at higher temperatures, it is recommended that the adhesive be cured a minimum of 36 hours to attain heat resistance assured to the temperatures stated in the description paragraph of this publication.
Although Aerocel® insulation does not require protective coating, if coating is required, all bonded joints should be allowed to cure for at least 24 to 36 hours. When sheet material is installed requiring full surface coverage of adhesive, it is recommended the insulation be allowed to cure for one full week before coating is applied.
Clean Up
Use either lacquer thinners or methyl ethyl ketone to clean any residue from tools.
Danger
Extremely flammable. Vapors from this product may ignite or cause flash fires. Use only in well ventilated areas, with all windows and doors open. Do not expose to heat, sparks or open flames. Take precaution in exposure to any heat source. Extinguish all flames, pilot lights, heaters, stoves or electric motors. Do not smoke in area of usage.
Close container immediately after use. Do not inhale vapors for prolonged periods of time or allow prolonged contact with skin. Do not take internally and keep away from children. Not for consumer use. This product is sold only for professional or industrial applications.
Fire Performance
ASTM E 84 test Method
Applied on Asbestos Cement board
Flame Spread .................... 5
Smoke Developed .........25
Read carefully all warnings on label before use.
Properties
Color: Amber 1 Black
Composition: Synthetic Rubber base with synthetic resins and fillers added
Coverage: 200 square feet per gallon under ideal conditions
Drying Time: 3-6 minutes under ideal conditions
Net Weight: 6.9 Ib. per gallon
Solids Content: Approx. 25% by weight
Shelf Life: 1 to 2 years in monitored storage
High Quality Self-Adhesive Insulation Foam Tape
Aerotape is a flexible and self adhering foam tape and is made from the same high quality EPDM material that our Aerocel® and Aerocel®-CG closed cell insulation is made from.
Aerotape is ideal for wrapping hot and cold pipe, tubing and fittings. Aerotape is easy to use and prevents condensation. Aerotape is designed to prevent heat gain, heat loss and prevent frost from forming on chilled water tubing and refrigeration lines.
Aerotape adheres firmly to all metal surfaces and is coated with selected pressure sensitive adhesive providing long service life.
Specification
Aerotape is 1/8” thick, 2” wide and 30' long. It is packed in individual cartons and then over packed in master cartons, 10 per carton.
Physical Properties
Composition: EPDM Closed cell elastomeric thermal insulation. Same material as our Aerocel® tube & sheet.
Color: Black
Density: 3 to 6 pounds per cubic foot ASTM D 1667
Thermal conductivity: 0.25 btu. In./ft3 hr. at 75° F
Water absorption: max. 5% by weight ASTM D 1056
Water vapor permeability: 0.10 perm-inch ASTM C 355
Temperature range: -70° F to ° F
| ||||||
Based on a closed-cell design, Aerocel® EPDM is the most efficient and versatile elastomeric insulation on the market. Aerocel® EPDM is designed for rugged applications including liquid cooling and heating pipes. And since EPDM is been used for decades as a roofing material, Aerocel® EPDM is inherently weather resistant – making it the perfect choice for harsh, outdoor applications. | ||||||
Key Features:
|
AEROFLEX یک عایق الاستومریک برودتی، حرارتی سلول بسته از جنس EPDM جهت عایق کاری سیستمهای حرارتی و برودتی مرکزی شامل لوله کشی آب سرد وگرم،مخازن، لوله های انتقال سیالات و گازهادر صنایع مختلف نظیر نفت، گاز،پتروشیمی، شیمیایی، خودرو سازی، نیروگاهی، کشتی سازی، هواپیماسازی، داروسازی و ساختمان به منظور ذخیره سازی انرژی و جلوگیری از ایجاد مشکلات ناشی از میعان میباشد.
AEROFLEX کاربرد وسیعی در سیستم H V A C &R در ساختمانها، کارخانجات و صنایع با استاندارد بین المللی بالا را داشته و دلیل آن خصوصیات برجسته زیر میباشد:
●مقاومت در برابر نفوذ بخار و رطوبت بدون نیاز به استفاده از موانع اضافی.
●ساختار سلولی کاملا بسته که نتیجه آن داشتن ضریب هدایت حرارتی (K-value) ثابت در زمان استفاده و همچنین جذب آن بسیار پایین و مقاومت بالا در برابر رطوبت می باشد.
●ساختار غیر قطبی با یک محور اشباع پلیمری که نتیجه آن مقاومت بالا در برابر اشعه ماورا بنفش (UV) شرایط جوی و عدم جذب رطوبت میباشد.
●فاقد مواد سمی، فیبر و ترکیبات نیتروژن دار
halogen, Nitrosamine, Dioxin, PVC, CFCs, (Non Formaldahyde
●ضریب انتقال حرارتی ثابت و پایین 0.034w/mk در دمای صفر درجه سانتیگراد.
●دامنه حرارتی در دماهای بین 200_ تا 125+ درجه سانتیگراد.
●بدون ایجاد حساسیت برای پوست و سیستم تنفسی.
●دارای استاندارد های بین المللی مقاومت در برابر دود و آتش گرفتگی.
●انعطاف پذیری و نصب آسان همراه با ظاهری تمیز و مرتب.
●جذب موثر صدا ( عایق صوتی 27db در ضخامت 20میلیمتر)
●بدون نیاز به پوشش های فلزی در لوله و مخازن.
●مقاوم در برابر رشد قارچها و حملات حشرات موذی.
●بهترین جایگزین پشم شیشه، پلی یورتان، پلی اتیلن و.....
●عدم اشتعال و مقاوم به آتش و حریق، خود خاموش شونده.
●وزن مخصوص بین 48 تا 96 کیلوگرم.
●پایین بودن غلظت دود در هنگام سوختن.
●مقاوم به مواد شیمیایی، اسیدهاو بازها.
●عدم تولید مواد سمی در هنگام آتش سوزی.
●دارای استاندارهای بین المللی:
ASTM_DNV_LLOYD'S_ANSI
BV_SGS_EMPA_IMO_BVQI
RUNE_LICM_GL_NKK